Devices You Need to Install a New Tub
Devices You Need to Install a New Tub
Blog Article
Just how do you actually feel with regards to A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't precisely rocket science, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is additionally a reasonably challenging task. If the old bathtub is readily easily accessible, the job can move immediately; if you have to open up a wall to remove the old tub and place the new bath tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to vacate the old tub and also set in the new one. Make certain you have certified yourself for the work as well as fit trying it. Rather than working with a professional to take over a halfway-completed job, it is better to think about employing one prior to you begin. Possibilities are you may need a specialist plumber to make tube connections.
This post will assist you install a brand-new bathtub in your washroom if you have already bought a brand-new bathtub as well as do not need to change the plan of your previous water supply pipelines.
Your tools as well as material list should make up the following:
Planning for the Installment
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets system to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of removing the existing faucets can be fairly problematic due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipes. When the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, put the bathtub in the required position. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level and also changing the feet on the bathtub until the level checks out level.
To mount faucets, fit the bottom of the outermost flexible faucet adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water system as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as additionally inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, repair the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub must wait up until the bathtub has actually been used at the very least when as this will resolve it into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in place in between the tap as well as the sink. Secure the tap in position with the producer given backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The previous type must be attached to the tap ends first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bath and the tiling, bring about problems with dampness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components and also installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly load the tub with water before securing, to permit the motion experienced when the tub remains in usage. The sealant can crack rather early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a person who reads about Tools You Need to Install a New Bathtub , I thought sharing that short article was smart. Do you know about another individual who is enthusiastic about How to Install a Bathtub Yourself? Do not hesitate to share it. Many thanks for your time spent reading it.
Go Deal
Report this page